The NFPA CWBSP Questions & Practice Test are Available On-Demand
Valid CWBSP Exam Dumps Ensure you a HIGH SCORE
NEW QUESTION # 52
When designing an early suppression fast-response (ESFR) fire sprinkler system, what shall the design area of the most hydraulically demanding area consist of?
- A. 14 sprinklers
- B. 960 ft2
- C. 1200 ft2
- D. 12 sprinklers
Answer: D
NEW QUESTION # 53
A kitchen in a restaurant encompasses an area of just over 700 ft2 (65 m2) with 2-hour fire rated walls. Does this meet the definition of a small room?
- A. No, 700 ft2 (65 m2) is too large.
- B. Yes, as the limit is 800 ft2 (74 m2).
- C. Yes, as the walls are 1-hour fire rated.
- D. No, small rooms are only of light hazard occupancy.
Answer: A
Explanation:
A kitchen area of over 700 ft² in a restaurant typically does not meet the definition of a "small room" in fire protection terminology, as it exceeds common size thresholds for such a classification, which often consider both the area and the specific use or hazard of the space.
References: NFPA standards and fire protection guidelines often define "small rooms" based on specific criteria related to size, use, and construction features, which vary across different applications and standards.
NEW QUESTION # 54
The minimum diameter of a private service main to a hydraulically calculated sprinkler system that also supplies a fire hydrant is
- A. 6 in. (150 mm).
- B. 4 in. (100 mm).
- C. 3 in. (75 mm).
- D. 8 in. (200 mm).
Answer: A
Explanation:
A minimum diameter of 6 inches for a private service main is common when the system also supplies a fire hydrant, ensuring adequate water supply for both the sprinkler system and firefighting needs.
References: NFPA standards and best practices related to water supply requirements for fire protection systems, ensuring sufficient capacity for hydrant and sprinkler system demands.
NEW QUESTION # 55
After reviewing an existing sprinkler system, it was determined that sprinklers were installed using NFPA 13 using the Ordinary Hazard Pipe Schedule method. The highest elevation of sprinklers is 28 ft (8.53m) and the system is fully monitored as specified by NFPA 13. What is the minimum pressure and flow required?
- A. 850 gpm at 32 psi (3,200 L/min at 2.2 bar)
- B. 500 gpm at 32 psi (1,900 L/min at 2.2 bar)
- C. 850 gpm at 27 psi (3,200 L/min at 1.86 bar)
- D. 500 gpm at 27 psi (1,900 L/min at 1.86 bar)
Answer: D
Explanation:
For a system using the Ordinary Hazard Pipe Schedule method, the minimum pressure and flow required are typically based on the system's design criteria, which for a system fully monitored as specified by NFPA 13 and with the highest elevation of sprinklers at 28 ft, would be around 500 gpm at 27 psi.
References: NFPA 13 includes guidelines for calculating system demand using the pipe schedule method, taking into account factors such as system elevation and monitoring.
NEW QUESTION # 56
When used for sprinkler system design, the water flow test shall be conducted no more than how many months prior to work plan submittal?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
Water flow tests for sprinkler system design should be conducted no more than 12 months prior to work plan submittal to ensure the test data accurately reflects current water supply conditions.
References: NFPA 13 requirements for water supply testing, ensuring that sprinkler system designs are based on up-to-date and accurate water supply information.
NEW QUESTION # 57
A 4 in. (102 mm) nominal diameter Schedule 10 sprinkler main is to be supported from the structure utilizing a trapeze hanger with a span of 8 ft (2.4 m). Using Schedule 40 pipe for the trapeze hanger, what is the minimum diameter pipe that should be used?
- A. 2.5 in. (65 mm)
- B. 2 in. (50 mm)
- C. 3 in. (75 mm)
- D. 1.5 in. (40 mm)
Answer: B
Explanation:
For supporting a 4 in. Schedule 10 sprinkler main with a trapeze hanger spanning 8 ft, a Schedule 40 pipe of at least 2 in. in diameter is typically recommended. This size provides adequate strength for the span and weight of the sprinkler main.
References: Engineering principles and best practices for hanger selection and sizing in sprinkler system installations.
NEW QUESTION # 58
The FPE has indicated that a vertical opening shall be protected by closely spaced sprinklers in combination with a draft stop installed per code. The sprinklers will be spaced 6 ft (1.83 m) on center. What is the minimum gpm discharge required per sprinkler head?
- A. 18 gpm (68 lpm)
- B. 15 gpm (57 lpm)
- C. 10 gpm (38 lpm)
- D. 20 gpm (76 lpm)
Answer: B
Explanation:
For closely spaced sprinklers protecting a vertical opening with a draft stop, a minimum discharge of 15 gpm per sprinkler head is commonly required to ensure sufficient water distribution and penetration for fire suppression within the protected area. This discharge rate provides a balance between efficiency and effectiveness in fire control.
References: General fire protection engineering principles and NFPA standards related to the design and installation of sprinkler systems for vertical openings.
NEW QUESTION # 59
What is the minimum design pressure for control mode specific application (CMSA) protection of a solid piled, Class IlI commodity stored 35 ft (11 m) high in a 40 ft (12 m) building?
- A. 30 psi (2.1 bar)
- B. 25 psi (1.7 bar)
- C. 16 psi (1.1 bar)
- D. 50 psi (3.4 bar)
Answer: B
Explanation:
For CMSA protection of solid piled Class III commodities stored up to 35 ft high in a building, a minimum design pressure of 25 psi is a typical requirement. This pressure ensures adequate water distribution and penetration for the depth and height of the storage.
References: NFPA 13 guidelines for the design and installation of CMSA sprinkler systems, tailored to specific storage configurations and commodity classifications.
NEW QUESTION # 60
A device for use in applications requiring special water discharge patterns, directional spray, or other unusual discharge characteristics, is known as a
- A. water mist nozzle.
- B. nozzie.
- C. CMSA sprinkler.
- D. special sprinkler.
Answer: D
Explanation:
A special sprinkler is a device for use in applications requiring special water discharge patterns, directional spray, or other unusual discharge characteristics, as defined by NFPA 13. Examples of special sprinklers include residential sprinklers, exposure protection sprinklers, water curtains, and sprinkler-protected glazing.
Special sprinklers have different design and installation requirements than standard spray sprinklers.
References: NFPA 13, 2019 edition, section 3.3.27.1; NFPA 13 Handbook, 2019 edition, page 31.
A special sprinkler is designed for specific applications that require unique water discharge patterns, directional spray, or other specialized discharge characteristics. These sprinklers are tailored for particular fire risks or architectural constraints where standard sprinklers may not provide adequate protection.
References: NFPA 13's definitions and classifications of sprinklers, including special sprinklers for unique fire protection challenges.
NEW QUESTION # 61
How much pressure is lost due to elevation in water flowing in a pipe from 6 ft (1.8 m) high to 15 ft (4.6 m) high?
- A. 3.897 psi (2.6850 bar)
- B. 3.6 psi (2.4804 bar)
- C. 4.5 psi (3.1005 bar)
- D. 4.050 psi (2.6850 bar)
Answer: A
Explanation:
The pressure lost due to elevation in water flowing from 6 ft to 15 ft high is approximately 3.897 psi, calculated based on the height difference and the principle that each foot of elevation change results in a pressure change of 0.433 psi.
References: Basic hydraulic principles applicable in fire protection engineering, which include calculating the impact of elevation changes on water pressure in a piping system.
NEW QUESTION # 62
What is the maximum pressure rating when using standard weight pattern malleable iron fittings that are 6 in.
(150 mm) in size and smaller?
- A. 400 psi (28 bar)
- B. 175 psi (12 bar)
- C. 300 psi (21 bar)
- D. 200 psi (14 bar)
Answer: C
Explanation:
Standard weight pattern malleable iron fittings that are 6 inches in size and smaller typically have a maximum pressure rating of 300 psi (21 bar). This rating ensures that the fittings can withstand the pressure demands of most fire sprinkler systems without failure.
References: Fitting manufacturers provide specifications for malleable iron fittings, including their pressure ratings, which must comply with standards such as those set forth by ASTM and ANSI.
NEW QUESTION # 63
When field acceptance testing a fire pump with a variable speed pressure limiting control, the pump shall be tested in variable speed mode at
- A. no flow, 100%, and 150% of rated load.
- B. no flow, and 100% of rated load.
- C. no flow, 25%, 50%, 75%, 100%, 125%, and 150% of rated load
- D. no flow, 50%, 100%, and 150% of rated load.
Answer: A
Explanation:
When field acceptance testing a fire pump with variable speed pressure limiting control, the pump should be tested in variable speed mode at no flow, 100%, and 150% of rated load to fully evaluate its performance under different demand conditions.
References: NFPA standards for fire pump testing, which outline procedures to ensure pumps perform effectively under various flow conditions, including no load and overload scenarios.
NEW QUESTION # 64
For a dry sprinkler installed in an insulated freezer box with an internal ambient temperature of -20°F (-29#) where the barrel is exposed to an ambient temperature area of 40°F (4C), what is the minimum exposed barrel length required?
- A. 12 in. (300 mm)
- B. 14 in. (350 mm)
- C. 16 in. (400 mm)
- D. 18 in. (450 mm)
Answer: D
Explanation:
For a dry sprinkler in a freezer with an internal temperature of -20°F and an external ambient temperature of
40°F, a minimum exposed barrel length of 18 in. is typically recommended. This length helps prevent freezing within the barrel while accommodating temperature differentials.
References: Installation guidelines for dry sprinklers in environments with significant temperature variations, ensuring system functionality and freeze protection.
NEW QUESTION # 65
An existing building with an existing sprinkler system is constructed with 26 in. (660 mm) beams framed into girders spaced on 7 ft (2.1 m) centers. What is the maximum distance permitted below the ceiling or roof deck if standard upright sprinklers are positioned in the center of each section?
- A. 22 in. (560 mm)
- B. 1 in. (25 mm)
- C. 6 in. (150 mm)
- D. 12 in. (300 mm)
Answer: D
Explanation:
When using standard upright sprinklers with beams framed into girders spaced on 7 ft centers, a maximum distance of 12 in. below the ceiling or roof deck is typically permitted. This ensures the sprinklers maintain effective coverage while accommodating architectural features.
References: NFPA 13 installation standards for upright sprinklers in relation to ceiling obstructions and beam configurations.
NEW QUESTION # 66
When welding is performed on sprinkler piping, which of these shall apply?
- A. Steel plates shall be welded to the ends of piping or fittings
- B. Fittings can penetrate the internal diameter of the piping
- C. Discs shall be retrieved
- D. Fittings shall be modified
Answer: C
Explanation:
When welding is performed on sprinkler piping, it is crucial that discs (or coupons) cut out during the welding process are retrieved. This ensures that the piping system remains clear of obstructions that could impede water flow during a fire event.
References: NFPA 13 and welding standards for piping systems emphasize the importance of maintaining the integrity and clear passage within fire protection piping systems.
NEW QUESTION # 67
When backflow prevention valves are installed on existing pipe scheduled systems, the friction losses of the device shall be accounted for when determining
- A. static pressure.
- B. residual pressure.
- C. system GPM requirements.
- D. system flow requirements.
Answer: B
Explanation:
When backflow prevention devices are added to a system, their associated friction losses can affect the residual pressure available for the sprinkler system operation. Therefore, it's important to account for these losses to ensure the system maintains the required pressure during operation.
References: NFPA 13 includes considerations for the installation of backflow preventers and their impact on system design, emphasizing the need to account for device-related friction losses to maintain adequate residual pressure in the sprinkler system.
NEW QUESTION # 68
In areas using HVLS fans, where must the fans be located in regards to sprinkler placement?
- A. Centered approximately between four adjacent sprinklers
- B. No requirement
- C. Centered approximately between two adjacent sprinklers
- D. As close to sprinklers as possible
Answer: A
Explanation:
According to NFPA 13, HVLS fans shall be centered approximately between four adjacent sprinklers to avoid interference with the sprinkler discharge pattern and to provide adequate clearance from the sprinkler deflectors. This requirement applies to both standard and ESFR sprinklers, and the fans shall be interlocked to shut down immediately upon a waterflow alarm.
References: NFPA 13, 2019 edition, section 11.1.71; NFPA 13 Handbook, 2019 edition, section 11.1.72; NFPA 13 Guidelines for Placing HVLS Fans in Sprinkler Protected Buildings; HVLS Fans and Fire Sprinklers
NEW QUESTION # 69
What piping material is acceptable for the suction and discharge piping pressure maintenance pumps?
- A. HDPE piping
- B. Listed CPVC piping
- C. Copper tube
- D. Black or galvanized steel piping
Answer: D
Explanation:
Black or galvanized steel piping is acceptable for the suction and discharge piping of pressuremaintenance (jockey) pumps in fire protection systems. These materials offer the necessary strength and durability for such applications.
References: NFPA 20 and related standards provide guidelines for materials suitable for use in fire pump installations, including piping for suction and discharge lines.
NEW QUESTION # 70
A warehouse has palletized storage of empty wood crates on wood pallets to a height of 11 ft (3.4 m). What is the minimum design density?
- A. 0.15 gpm/ft2 (6.1 mm/min)
- B. 0.23 gpm/ft2 (9.2 mm/min)
- C. 0.25 gpm/ft2 (10.2 mm/min)
- D. 0.20 gpm/ft2 (8.1 mm/min)
Answer: D
Explanation:
The minimum design density for protecting palletized storage of empty wood crates on wood pallets up to a certain height is determined by considering the combustibility of the materials and the configuration of the storage. A design density of 0.20 gpm/ft² is often recommended for such light hazard commodities to provide adequate water distribution over the fire area.
References: NFPA 13 guidelines for calculating design densities based on the type of commodity, storage arrangement, and height of storage.
NEW QUESTION # 71
Which type of pipe does not require a special listing to use threaded fittings?
- A. Schedule 40
- B. Schedule 5
- C. Schedule 10
- D. Schedule 7
Answer: A
Explanation:
Schedule 40 pipe does not require a special listing to use threaded fittings, as it is a common standard for pipe thickness and is widely used in fire protection systems for its durability and compatibility with standard fittings.
References: Piping standards and fire protection system design practices, where Schedule 40 pipe is a common choice for its balance of strength and workability.
NEW QUESTION # 72
What is the minimum temperature rating of ceiling sprinklers in roll paper stored at 15 ft. (4.6 m) or less?
- A. 135°F (57°C)
- B. 100°F (38°C)
- C. 150°F (66#)
- D. 175°F (79#)
Answer: C
Explanation:
The minimum temperature rating for ceiling sprinklers in roll paper storage areas that are 15 ft or less in height is typically 150°F (66°C). This rating is selected to provide a buffer between the ambient temperature conditions and the activation temperature of the sprinklers, preventing accidental activation.
References: NFPA 13 outlines temperature rating requirements for sprinklers based on the occupancy and storage configurations to ensure appropriate activation in the event of a fire.
NEW QUESTION # 73
......
CWBSP Exam Practice Questions prepared by NFPA Professionals: https://www.testkingit.com/NFPA/latest-CWBSP-exam-dumps.html
Pass CWBSP Exam with Latest Questions: https://drive.google.com/open?id=1x62l0zv97TH1ebkrI7Zkp91NtBf323Y1