JN0-351 Exam Brain Dumps - Study Notes and Theory [May-2024]
100% Guaranteed Results JN0-351 Unlimited 67 Questions
Juniper JN0-351 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
NEW QUESTION # 30
Exhibit
Your BGP neighbors, one in the USA and one in France, are not establishing a connection with each other.
Referring to the exhibit, which statement is correct?
- A. The BFD liveness is set too high.
- B. The BFD liveness is set too low.
- C. The BFD liveness must be configured on the BGP neighbor.
- D. The BFD liveness must be configured on the BGP group.
Answer: C
Explanation:
Explanation
The exhibit shows the configuration of BFD liveness detection for BGP at the global level, which applies to all BGP neighbors by default1. However, this configuration does not specify the session mode, which determines whether BFD uses single-hop or multihop mode to communicate with a neighbor2.
For single-hop BGP neighbors, which are directly connected on the same subnet, the session mode can be either automatic or single-hop. For multihop BGPneighbors, which are not directly connected and require multiple hops to reach, the session mode must be multihop2.
Since your BGP neighbors are in different countries, they are likely to be multihop neighbors. Therefore, you need to configure the session mode as multihop for each neighbor individually at the [edit protocols bgp group group-name neighbor address bfd-liveness-detection] hierarchy level2. For example:
protocols { bgp { group usa { neighbor 192.0.2.1 { bfd-liveness-detection { session-mode multihop; } } } group france { neighbor 198.51.100.1 { bfd-liveness-detection { session-mode multihop; } } } } } If you do not configure the session mode for multihop neighbors, BFD will use the default mode of automatic, which will try to use single-hop mode and fail to establish a BFD session with the remote neighbor2. This will prevent BGP from using BFD to detect liveliness and failover.
Therefore, the answer B is correct, as you need to configure the BFD liveness detection on the BGP neighbor level with the appropriate session mode for multihop neighbors.
NEW QUESTION # 31
You want to ensure traffic is routed through a GRE tunnel.
In this scenario, which two statements will satisfy this requirement? (Choose two.)
- A. All intermediary devices must have a route to the tunnel endpoints.
- B. BFD must be used on the stateless tunneling protocols.
- C. Tunnel endpoints must have a route that directs traffic into the tunnel.
- D. Keepalives must be used on stateless tunneling protocols.
Answer: A,C
Explanation:
Explanation
Option A is correct. For traffic to be sent through a GRE tunnel, there must be a route that directs the traffic into the tunnel. This is typically accomplished through the use of a static route or a dynamic routing protocol.
Option B is correct. All intermediary devices must have a route to the tunnel endpoints34. In real-world scenarios, the tunnel endpoints for a tunnel going over the Internet must have globally reachable internet addresses. Otherwise, intermediate routers in the Internet cannot forward the tunneled packets.
NEW QUESTION # 32
What is the maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation?
- A. 1480 bytes
- B. 1500 bytes
- C. 1496 bytes
- D. 1476 bytes
Answer: D
Explanation:
Explanation
The maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation is 1476 bytes1. This is because GRE packets are formed by the addition of the original packets and the required GRE headers1. These headers are 24-bytes in length and since these headers are added to the original frame, depending on the original size of the packet we may run into IP MTU problems1. The most common IP MTU is 1500-bytes in length (Ethernet)1. When the tunnel is created, it deducts the 24-bytes it needs to encapsulate the passenger protocols and that is the IP MTU it will use1. For example, if we are forming a tunnel over FastEthernet (IP MTU 1500)the IOS calculates the IP MTU on the tunnel as: 1500-bytes from Ethernet -
24-bytes for the GRE encapsulation = 1476-Bytes1.
NEW QUESTION # 33
What are two reasons for creating multiple areas in OSPF? (Choose two.)
- A. to increase the size of the LSDB
- B. to reduce LSA flooding across the network
- C. to increase the number of adjacencies in the backbone
- D. to reduce the convergence time
Answer: B,D
Explanation:
Explanation
Option A is correct. Creating multiple areas in OSPF can help to reduce the convergence time . This is because changes in one area do not affect other areas, so fewer routers need to run the SPF algorithm in response to a change.
Option D is correct. Creating multiple areas in OSPF can help to reduce Link State Advertisement (LSA) flooding across the network. This is because LSAs are not flooded out of their area of origin.
NEW QUESTION # 34
Which statement is correct about controlling the routes installed by a RIB group?
- A. An import policy is applied to the RIB group.
- B. Only routes in the last table are installed.
- C. A firewall filter must be configured to install routes in the RIB groups.
- D. An export policy is applied to the RIB group.
Answer: A
Explanation:
Explanation
A RIB group is a configuration that allows a routing protocol to install routes into multiple routing tables in Junos OS. A RIB group consists of an import-rib statement,which specifies the source routing table, and an export-rib statement, which specifies the destination routing table or group. A RIB group can also include an import-policy statement, which specifies one or more policies to control which routes are imported into the destination routing table or group1.
An import policy is a policy statement that defines the criteria for accepting or rejecting routes from the source routing table. An import policy can also modify the attributes of the imported routes, such as preference, metric, or community. An import policy can be applied to a RIB group by using the import-policy statement under the [edit routing-options rib-groups] hierarchy level1.
Therefore, option A is correct, because an import policy is applied to the RIB group to control which routes are installed in the destination routing table or group. Option B is incorrect, because all routes in the source routing table are imported into the destination routing table or group, unless filtered by an import policy.
Option C is incorrect, because a firewall filter is not used to install routes in the RIB groups; a firewall filter is used to filter packets based on various criteria. Option D is incorrect, because an export policy is not applied to the RIB group; an export policy is applied to a routing protocol to control which routes are advertised to other devices.
References:
1: rib-groups | Junos OS | Juniper Networks
NEW QUESTION # 35
You need to configure a LAG between your switches. In this scenario, which two statements are correct?
(Choose two.)
- A. Duplex and speed settings are not required to match on both participating devices.
- B. Member links are not required to be contiguous ports.
- C. Duplex and speed settings are required to match on both participating devices.
- D. Member links are required to be contiguous ports.
Answer: B,C
Explanation:
B is correct because duplex and speed settings are required to match on both participating devices. According to the Juniper Networks documentation1, all the interfaces in a LAG must have the same speed and be in full-duplex mode. This ensures that the LAG can operate as a single logical link without any performance or compatibility issues.
C is correct because member links are not required to be contiguous ports. According to the Juniper Networks documentation2, you can group any Ethernet interfaces on a switch into a LAG, regardless of their physical location or slot number. This provides flexibility and scalability for configuring LAGs on switches.
NEW QUESTION # 36
Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)
- A. Layer 2 control traffic is permitted on the secondary link.
- B. Redundant trunk groups load balance traffic across two designated uplink interfaces.
- C. Redundant trunk groups use spanning tree to provide loop-free redundant uplinks.
- D. If the active link fails, then the secondary link automatically takes over.
Answer: A,D
Explanation:
C is correct because Layer 2 control traffic is permitted on the secondary link of a redundant trunk group (RTG) on EX Series switches. Layer 2 control traffic includes protocols such as LLDP, LACP, and STP, which are used to exchange information and coordinate actions between switches1. According to the Juniper Networks documentation2, Layer 2 control traffic is allowed to pass through both the active and the secondary links of an RTG, but data traffic is only forwarded through the active link. This allows the switches to maintain their Layer 2 adjacencies and monitor the link status on both links.
D is correct because if the active link fails, then the secondary link automatically takes over in an RTG on EX Series switches. An RTG consists of two trunk links: an active or primary link, and a secondary or backup link2. The active link is used to forward data traffic, while the secondary link is in standby mode. If the active link fails or becomes unavailable, the secondary link immediately transitions to a forwarding state and takes over the data traffic without waiting for normal STP convergence2. This provides fast recovery and redundancy for the network.
NEW QUESTION # 37
Exhibit
Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)
- A. On R3 enable Level 1 on the ge-0/0/4 interface
- B. On R1, enable Level 1 on the ge-0/0/1 interface.
- C. On R1, disable Level 2 on the ge-0/0/1 interface.
- D. On R3 disable Level 2 on the ge-0/0/4 interface.
Answer: A,B
Explanation:
Explanation
A: On R1, enable Level 1 on the ge-0/0/1 interface. In IS-IS, both levels (Level 1 and Level 2) are enabled by default when you enable IS-IS on an interface1. Level 1 systems route within an area2. If the destination is outside an area, Level 1 systems route toward a Level 2 system2. Therefore, enabling Level 1 on the ge-0/0/1 interface on R1 would allow packets to reach from R1 to R3.
D: On R3 enable Level 1 on the ge-0/0/4 interface Similarly, enabling Level 1 on the ge-0/0/4 interface on R3 would allow packets to reach from R1 to R3.
These explanations are based on the IS-IS configuration documents and learning resources available at Juniper Networks1 and Cisco34.
NEW QUESTION # 38
Which statement is correct about IP-IP tunnels?
- A. The TTL in the inner packet is decremented during transit to the tunnel endpoint.
- B. IP-IP tunnels only support encapsulating IP traffic.
- C. IP-IP tunnels only support encapsulating non-IP traffic.
- D. There are 24 bytes of overhead with IP-IP encapsulation.
Answer: B
Explanation:
Explanation
IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels only support encapsulating IP traffic, which means that the payload of the inner packet must be an IP packet. IP-IP tunnels cannot encapsulate non-IP traffic, such as Ethernet frames or MPLS labels1.
Option A is correct, because IP-IP tunnels only support encapsulating IP traffic. Option B is incorrect, because IP-IP tunnels only support encapsulating non-IP traffic. Option C is incorrect, because the TTL in the inner packet is not decremented during transit to the tunnel endpoint. The TTL in the outer packet is decremented by each router along the path, but the TTL in the inner packet is preserved until it reaches the tunnel endpoint2.
Option D is incorrect, because there are 20 bytes of overhead with IP-IP encapsulation. The overhead consists of the header of the outer packet, which has a fixed size of 20 bytes for IPv43.
References:
1: IP-IP Tunneling 2: What is tunneling? | Tunneling in networking 3: IPv4 - Header
NEW QUESTION # 39
You are asked to create a new firewall filter to evaluate Layer 3 traffic that is being sent between VLANs. In this scenario, which two statements are correct? (Choose two.)
- A. You should apply the firewall filter to the appropriate VLAN.
- B. You should apply the firewall filter to the appropriate IRB interface.
- C. You should create a family inet firewall filter with the appropriate match criteria and actions.
- D. You should create a family Ethernet-switching firewall filter with the appropriate match criteria and actions.
Answer: B,C
Explanation:
Explanation
A firewall filter is a configuration that defines the rules that determine whether to forward or discard packets at specific processing points in the packet flow. A firewall filter can also modify the attributes of the packets, such as priority, marking, or logging. A firewall filter can be applied to various interfaces, protocols, or routing instances on a Juniper device1.
A firewall filter has a family attribute, which specifies the type of traffic that the filter can evaluate. The family attribute can be one of the following: inet, inet6, mpls, vpls, iso, or ethernet-switching2. The family inet firewall filter is used to evaluate IPv4 traffic, which is the most common type of Layer 3 traffic on a network.
To create a family inet firewall filter, you need to specify the appropriate match criteria and actions for each term in the filter. The match criteria can include various fields in the IPv4 header, such as source address, destination address, protocol, port number, or DSCP value. The actions can include accept, discard, reject, count, log, policer, or next term3.
To apply a firewall filter to Layer 3 traffic that is being sent between VLANs, you need to apply the filter to the appropriate IRB interface. An IRB interface is an integrated routing and bridging interface that provides Layer 3 functionality for a VLAN on a Juniper device. An IRB interface has an IP address that acts as the default gateway for the hosts in the VLAN. An IRB interface can also participate in routing protocols and forward packets to other VLANs or networks4.
Therefore, option C is correct, because you should create a family inet firewall filter with the appropriate match criteria and actions. Option D is correct, because you should apply the firewall filter to the appropriate IRB interface.
Option A is incorrect, because you should not create a family ethernet-switching firewall filter with the appropriate match criteria and actions. A family ethernet-switching firewall filter is used to evaluate Layer 2 traffic on a Juniper device. A family ethernet-switching firewall filter can only match on MAC addresses or VLAN IDs, not on IP addresses or protocols5.
Option B is incorrect, because you should not apply the firewall filter to the appropriate VLAN. A VLAN is a logical grouping of hosts that share the same broadcast domain on a Layer 2 network. A VLAN does not have an IP address or routing capability. A firewall filter cannot be applied directly to a VLAN; it must be applied to an interface that belongs to or connects to the VLAN6.
References:
1: Firewall Filters Overview 2: Configuring Firewall Filters 3: Configuring Firewall Filter Match Conditions and Actions 4: Understanding Integrated Routing and Bridging Interfaces 5: Configuring Ethernet-Switching Firewall Filters 6: Understanding VLANs
NEW QUESTION # 40
Exhibit
Referring to the exhibit, which statement is correct?
- A. The root bridge has not been elected for this RSTP topology.
- B. The local device is using a bridge priority of 4k.
- C. The root bridge is using a bridge priority of 4k.
- D. The local device is the root bridge for this RSTP topology.
Answer: D
Explanation:
Explanation
In a Rapid Spanning Tree Protocol (RSTP) topology, the root bridge is determined by the switch with the lowest bridge priority value12. If all switches have the same priority, then the root bridge is assigned to the switch whose MAC address's hex value is the lowest2. The default bridge priority value is 3276832. However, without the actual exhibit, it's difficult to definitively determine which device is the root bridge. But based on the options provided, if we assume that the local device has a lower bridge priority or a lower MAC address than other devices in the network, then it could be considered as the root bridge for this RSTP topology45.
NEW QUESTION # 41
Which two mechanisms are part of building and maintaining a Layer 2 bridge table? (Choose two.)
- A. flooding
- B. blocking
- C. learning
- D. listening
Answer: A,C
Explanation:
Option B is correct. Flooding is a mechanism used in Layer 2 bridging where the switch sends incoming packets to all its ports except for the port where the packet originated1. This is done when the switch doesn't know the destination MAC address or when the packet is a broadcast or multicast1.
Option C is correct. Learning is another mechanism used in Layer 2 bridging where the switch learns the source MAC addresses of incoming packets and associates them with the port on which they were received23. This information is stored in a MAC address table, also known as a bridge table23.
Option A is incorrect. Blocking is a state in Spanning Tree Protocol (STP) used to prevent loops in a network2. It's not a mechanism used in building and maintaining a Layer 2 bridge table2.
Option D is incorrect. Listening is also a state in Spanning Tree Protocol (STP) where the switch listens for BPDUs to make sure no loops occur in the network before transitioning to the learning state2. It's not a mechanism used in building and maintaining a Layer 2 bridge table2.
NEW QUESTION # 42
Exhibit.
You want to enable redundancy for the EBGP peering between the two routers shown in the exhibit. Which three actions will you perform in this scenario? (Choose three.)
- A. Configure an MD5 peer authentication.
- B. Configure loopback interface peering.
- C. Configure BGP multihop.
- D. Configure routes for the peer loopback interface IP addresses.
- E. Configure a cluster ID.
Answer: B,C,D
Explanation:
A is correct because you need to configure BGP multihop to enable redundancy for the EBGP peering between the two routers. BGP multihop is a feature that allows BGP peers to establish a session over multiple hops, instead of requiring them to be directly connected1. By default, EBGP peers use a time-to-live (TTL) value of 1 for their packets, which means that they can only reach adjacent neighbors1. However, if you configure BGP multihop with a higher TTL value, you can allow EBGP peers to communicate over multiple routers in between1. This can provide redundancy in case of a link failure or a router failure between the EBGP peers.
B is correct because you need to configure loopback interface peering to enable redundancy for the EBGP peering between the two routers. Loopback interface peering is a technique that uses loopback interfaces as the source and destination addresses for BGP sessions, instead of physical interfaces2. Loopback interfaces are virtual interfaces that are always up andreachable as long as the router is operational2. By using loopback interface peering, you can avoid the dependency on a single physical interface or link for the BGP session, and use multiple paths to reach the loopback address of the peer2. This can provide redundancy and load balancing for the EBGP peering.
C is correct because you need to configure routes for the peer loopback interface IP addresses to enable redundancy for the EBGP peering between the two routers. Routes for the peer loopback interface IP addresses are necessary to ensure that the routers can reach each other's loopback addresses over multiple hops2. You can use static routes or dynamic routing protocols to advertise and learn the routes for the peer loopback interface IP addresses2. Without these routes, the routers will not be able to establish or maintain the BGP session using their loopback interfaces.
NEW QUESTION # 43
Exhibit
What does the * indicate in the output shown in the exhibit?
- A. All interfaces have elected a root bridge.
- B. The interface is down.
- C. The interface is active.
- D. The switch ports have a router attached.
Answer: C
Explanation:
The exhibit shows the output of the command show vlans brief, which displays brief information about VLANs and their associated interfaces1.
The output has four columns: Routing instance, VLAN name, Interfaces, and Tagging.
The * symbol indicates that the interface is active, meaning that it is up and forwarding traffic1. This can be verified by the command , which displays the status of the interfaces2.
NEW QUESTION # 44
Exhibit
You are a network operator troubleshooting BGP connectivity.
Which two statements are correct about the output shown in the exhibit? (Choose two.)
- A. The BGP session is not established.
- B. The R1 is configured for AS 65400.
- C. Peer 10.32.1.2 is configured for AS 63645.
- D. The routers are exchanging IPv4 routes.
Answer: A,B
Explanation:
Explanation
Option B suggests that the BGP session is not established. This is correct because in the output, the state of the BGP session is shown as "Idle". In BGP, an "Idle" state means that the BGP session is not currently established1.
Option C suggests that R1 is configured for AS 65400. This is also correct because in the output, it's shown that the local AS number is 654001. The local AS number represents the Autonomous System (AS) number of the router on which you're checking the BGP session1.
NEW QUESTION # 45
What are two characteristics of RSTP alternate ports? (Choose two.)
- A. RSTP alternate ports are active ports used to forward frames toward the root bridge.
- B. RSTP alternate ports block traffic while receiving superior BPDUs from a neighboring switch.
- C. RSTP alternate ports provide an alternate lower cost path to the root bridge.
- D. RSTP alternate ports provide an alternate higher cost path to the root bridge.
Answer: B,D
Explanation:
A is correct because RSTP alternate ports block traffic while receiving superior BPDUs from a neighboring switch. An alternate port is a backup port for a root port, which means it receives better BPDUs from another bridge than the current root port1. However, an alternate port does not forward any traffic, as it is in a discarding state2. It only listens to BPDUs and waits for the root port to fail. If the root port fails, the alternate port can immediately transition to a forwarding state and become the new root port1.
C is correct because RSTP alternate ports provide an alternate higher cost path to the root bridge. An alternate port is selected based on the same criteria as the root port, which are the lowest bridge ID, the lowest path cost, the lowest sender port ID, and the lowest receiver port ID3. However, an alternate port receives a higher cost BPDU than the root port, otherwise it would be the root port itself1. Therefore, an alternate port provides an alternate higher cost path to the root bridge than the root port.
NEW QUESTION # 46
You are troubleshooting a BGP routing issue between your network and a customer router and are reviewing the BGP routing policies. Which two statements are correct in this scenario? (Choose two.)
- A. Import policies are applied to routes in the RIB-Local table.
- B. Export policies are applied to routes in the RIB-ln table.
- C. Import policies are applied after the RIB-ln table.
- D. Export policies are applied after the RIB-Local table.
Answer: C,D
Explanation:
Explanation
In BGP, routing policies are used to control the flow of routing information between BGP peers1.
Option C suggests that import policies are applied after the RIB-In table. This is correct because import policies in BGP are applied to routes that are received from a BGP peer, before they are installed in the local BGP Routing Information Base (RIB-In)1. The RIB-In is a database that stores all the routes that are received from all peers1.
Option D suggests that export policies are applied after the RIB-Local table. This is correct because export policies in BGP are applied to routes that are being advertised to a BGP peer, after they have been selected from the local BGP Routing Information Base (RIB-Local)1. The RIB-Local is a database that stores all the routes that the local router is using1.
Therefore, options C and D are correct.
NEW QUESTION # 47
Exhibit
You have configured a GRE tunnel. To reduce the risk of dropping traffic, you have configured a keepalive OAM probe to monitor the state of the tunnel; however, traffic drops are still occurring.
Referring to the exhibit, what is the problem?
- A. For GRE tunnels, the OAM protocol requires that the BFD protocols also be used.
- B. The "event link-adjacency-loss" option must be set.
- C. The hold-time value must be two times the keepalive-time value
- D. LLDP needs to be removed from the gr-1/1/10.1 interface.
Answer: C
Explanation:
Explanation
A keepalive OAM probe is a mechanism that can be used to monitor the state of a GRE tunnel and detect any failures in the tunnel path. A keepalive OAM probe consists of sending periodic packets from one end of the tunnel to the other and expecting a reply. If no reply is received within a specified time, the tunnel is considered down and the line protocol of the tunnel interface is changed to down1.
To configure a keepalive OAM probe for a GRE tunnel, you need to specify two parameters: the keepalive-time and the hold-time. The keepalive-time is the interval between each keepalive packet sent by the local router. The hold-time is the maximum time that the local router waits for a reply from the remote router before declaring the tunnel down2.
According to the Juniper Networks documentation, the hold-time value must be two times the keepalive-time value for a GRE tunnel2. This is because the hold-time value must account for both the round-trip time of the keepalive packet and the processing time of the remote router. If the hold-time value is too small, it may cause false positives and unnecessary tunnel flaps.
In the exhibit, the configuration shows that the keepalive-time is set to 10 seconds and the hold-time is set to
15 seconds for the gr-1/1/10.1 interface. This means that the local router will send a keepalive packet every 10 seconds and will wait for 15 seconds for a reply from the remote router. However, this hold-time value is not two times the keepalive-time value, which violates the recommended configuration. This may cause traffic drops if the remote router takes longer than 15 seconds to reply.
Therefore, option D is correct, because the hold-time value must be two times the keepalive-time value for a GRE tunnel. Option A is incorrect, because BFD is not required for GRE tunnels; BFD is another protocol that can be used to monitor tunnels, but it is not compatible with GRE keepalives3. Option B is incorrect, because the "event link-adjacency-loss" option is not related to GRE tunnels; it is an option that can be used to trigger an action when a link goes down4. Option C is incorrect, because LLDP does not need to be removed from the gr-1/1/10.1 interface; LLDP is a protocol that can be used to discover neighboring devices and their capabilities, but it does not interfere with GRE tunnels5.
References:
1: Configuring Keepalive Time and Hold time for a GRE Tunnel Interface 2: keepalive | Junos OS | Juniper Networks 3: Configuring Bidirectional Forwarding Detection 4: event link-adjacency-loss | Junos OS | Juniper Networks 5: Understanding Link Layer Discovery Protocol
NEW QUESTION # 48
What is a purpose of using a spanning tree protocol?
- A. to eliminate broadcast storms
- B. to tunnel Ethernet frames
- C. to route IP packets
- D. to look up MAC addresses
Answer: A
Explanation:
A broadcast storm is a network condition where a large number of broadcast packets are sent and received by multiple devices, causing congestion and performance degradation1. A broadcast storm can occur when there are loops in the network topology, meaning that there are multiple paths between two devices2.
A spanning tree protocol is a network protocol that prevents loops from being formed when switches or bridges are interconnected via multiple paths. It does this by creating a logical tree structure that spans all the devices in the network, and disabling or blocking the links that are not part of the tree, leaving a single active path between any two devices3.
By eliminating loops, a spanning tree protocol also eliminates broadcast storms, as broadcast packets will not be forwarded endlessly along the looped paths. Instead, broadcast packets will be sent only along the tree structure, reaching each device once and avoiding congestion3.
NEW QUESTION # 49
Which two statements correctly describe RSTP port roles? (Choose two.)
- A. The designated port forwards data to the downstream network segment or device.
- B. The root port is responsible for forwarding data to the root bridge.
- C. The backup port is used as a backup for the root port.
- D. The alternate port is a standby port for an edge port.
Answer: A,B
Explanation:
Explanation
In Rapid Spanning Tree Protocol (RSTP), there are several port roles that determine the behavior of the port in the spanning tree1.
Option A suggests that the designated port forwards data to the downstream network segment or device. This is correct because the designated port is the port on a network segment that has the best path to the root bridge1. It's responsible for forwarding frames towards the root bridge and sending configuration messages into its segment1.
Option D suggests that the root port is responsible for forwarding data to the root bridge. This is also correct because the root port is always the link directly connected to the root bridge, or the shortest path to the root bridge1. It's used to forward traffic towards the root bridge1.
Therefore, options A and D are correct.
NEW QUESTION # 50
What is the default keepalive time for BGP?
- A. 90 seconds
- B. 60 seconds
- C. 30 seconds
- D. 10 seconds
Answer: B
Explanation:
Explanation
The default keepalive time for BGP is 60 seconds1. The keepalive time is the interval at which BGP sends keepalive messages to maintain the connection with its peer1. If the keepalive message is not received within the hold time, the connection is considered lost1. By default, the hold time is three times the keepalive time, which is 180 seconds1.
NEW QUESTION # 51
......
JN0-351 Dumps PDF - Want To Pass JN0-351 Fast: https://www.testkingit.com/Juniper/latest-JN0-351-exam-dumps.html
JN0-351 Practice Exam Dumps Exam: https://drive.google.com/open?id=13B8afx_b1nRCJXvHWeRGk04ffdqwC_El