Get HP HPE0-S60 Dumps Questions [2023] To Gain Brilliant Result
HPE0-S60 dumps - TestKingIT - 100% Passing Guarantee
NEW QUESTION # 39
What is a restriction of using a RoCE network?
- A. It does not support Private VLAN and Multicast VLAN.
- B. It is by default configured as an untagged network and cannot be a part of a network set.
- C. It does not support smart link and private network features.
- D. it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
Answer: B
NEW QUESTION # 40
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A. Both master modules are located in the same HPE S ynergy frame
- B. To use interconnect bay set 3, all compute nodes must be half-height
- C. For the given downlink speed, the maximum number of frames is reached
- D. The master modules are located in the interconnect bays 2 and 5
Answer: A
NEW QUESTION # 41
Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?
- A. HPE OneView IT HPE Persistent Memory firmware must be updated.
- B. RMC CLI to update I/O and HPE Persistent Memory firmware
- C. HPE SUM if HPE Persistent Memory firmware must be updated
- D. HPE OneView method for I/O firmware update procedure
Answer: B
NEW QUESTION # 42
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard licenses for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options Which statement about this proposal is true?
- A. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
- B. vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
- C. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.
- D. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
Answer: B
NEW QUESTION # 43
You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.
Put the steps to achieve this goal into the coned order in the answer area on the right.
Answer:
Explanation:
1 - Create a logical interconnect group with uplink sets.
2 - Create a logical enciosure.
3 - Create an enciosure group.
4 - Create server profile templates and server profiles.
5 - Define all required networks.
NEW QUESTION # 44
Your customer is implementing an HPE Synergy solution based on three frames.
Click each of the ports that can be used to connect satellite modules.
Answer:
Explanation:
NEW QUESTION # 45
Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.
- A. HPE OneView Firmware Compliance Report
- B. HPE OneView Update Readiness Checker
- C. HPE OneView Global Dashboard
- D. HPE Composer Maintenance Console
Answer: D
NEW QUESTION # 46
Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?
- A. FC connectivity on the modules should be enabled through the service console by disabling FCoE.
- B. Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules
- C. Enter both modules into a maintenance mode, then enable FC connectivity through CLI
- D. Enable FC primary and secondary boot on the modules through the HPE OneView interface
Answer: A
NEW QUESTION # 47
Match each HPE OneView network type with its definition.
Answer:
Explanation:
NEW QUESTION # 48
Which statement about an HPE Oneview support dump is true?
- A. Support dump is a binary file that can be opened only in a dedicated application
- B. Preview support dump is available only when creating an appliance support dump
- C. Support dump can be created if HPE Virtual Connect modules are installed in the frame
- D. Appliance support dump by default contains a logical enclosure support dump
Answer: A
NEW QUESTION # 49
Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant Gen 10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?
- A. To use the required plugins HPE ProLiant Gen10 systems must be managed using HPE OneView
- B. HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers
- C. HPE Storage integration Pack for VMware vCenter does not support MSA arrays
- D. Both HPE Synergy Gen10 full-height compute module plugins will require a license
Answer: B
NEW QUESTION # 50
Your customer manages an HPE Synergy platform using HPE OneView 5.6. To leverage new functionalities, the customer wants to update HPE OneView to version 61 Which statement about this update process is true?
- A. The customer can update directly to 6,1, but HPE OneView downtime will be longer.
- B. Before updating to 6,1, customer should increase memory size on the HPE Composer.
- C. To update to 6,1, the customer has to first update to 6 0, which is a milestone edition.
- D. The customer must check the HPE Composer version, as 61 is supported only with HPE Composer2.
Answer: D
NEW QUESTION # 51
Click the area within the iLO management interface that will allow you to access workload Advisor.
Answer:
Explanation:
NEW QUESTION # 52
Your customer has a logical enclosure configured using a angle HPE Synergy frame with the following configuration
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- two HPE Synergy Virtual Connect SE 32Gb FC Modules -12 HPE Synergy 480 Gen10 Plus compute nodes with appropriate mezzanine cards They plan to add a new HPE Synergy frame to an existing logical enclosure with the following configuration
- two HPE Synergy Virtual Connect SE 32Gb FC Modules
- two HPE Synergy 20Gb interconnect Link Modules
- Eight HPE Synergy 480 Gen 10 Plus compute nodes with appropriate mezzanine cards Which statement about the planned configuration change is true?
- A. A license for an extended logical enclosure must be added to HPE OneView through GUI
- B. The HPE Synergy virtual Connect SE 32Gb FC Modules from both frames should be stacked
- C. Four compute modules must be moved to the second frame to balance the configuration
- D. The two HPE Synergy 20Gb interconnect Link Modules must be replace with the 50Gb option
Answer: B
NEW QUESTION # 53
As a result of the troubleshooting process, you recommend replacing, HPE Synergy Composer modules which HPE Synergy Composer 2 Why would you recommend this change?
- A. HPE Composer 2 provides access to 105 interface that can be used for full management of HPE Composer 2 remotely
- B. HPE Composer 1 running HPE OneView 5 2 or later can support only 12 frames within a single management nog
- C. HPE Composer 2 can support more than the maximum 21 frames that are supported with HPE Composer 1 and HPE OneView.
- D. HPE Composer 1 cannot support remote frames, which doubles the configuration and management procedures effort
Answer: B
NEW QUESTION # 54
Match HPE SimpliVity team with the definition.
Answer:
Explanation:
NEW QUESTION # 55
Your customer plans to deploy ESXi systems to HPE Synergy and HPE ProLiant servers using HPE OneView for VMware vCenter Server.
Which statement about HPE OneView for VMware vCenter Server functionality is true for this environment?
- A. HPE Synergy requires HPE Composer 2 for full functionality of HPE OneView for VMware vCenter Server
- B. Only systems managed using HPE Oneview can use HPE Oneview for VMware vCenter Server functionalities
- C. HPE ProLiant servers need an HPE OneView for VMware vCenter Server license for full functionality
- D. Individual systems can be added to HPE OneView for VMware vCenter Server through an ILO management processor
Answer: C
NEW QUESTION # 56
An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement
Answer:
Explanation:
NEW QUESTION # 57
Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.
Which statement regarding this setup is true?
- A. Interconnect modules that provide SAS connectivity should be moved to the third fabric
- B. Compute nodes must have a second CPU installed to access the second fabric.
- C. Each interconnect module in each fabric must be properly licensed in HPE OneView
- D. Each compute node must have at least 768GB of memory installed
Answer: D
NEW QUESTION # 58
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)
- A. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- B. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- C. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
- D. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- E. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- F. Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
Answer: A,B
NEW QUESTION # 59
Which statement about login redistribution is true?
- A. Login redistribution is available only If HPE Primera or HPE Alletra is connected directly to the HPE Synergy frame
- B. Login redistribution is used for login balancing when they are not distributed evenly over the FC links
- C. Login redistribution is a licensed feature and the number of licenses required depends on the number of active ports
- D. Login redistribution is supported only on the HPE Synergy Virtual Connect SE 32Gb FC Modules
Answer: D
NEW QUESTION # 60
You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group What should you check to fix the issue?
- A. if the logical enclosure is configured with redundant master modules
- B. if both FiexNICs are connected to different networks
- C. If the logical enclosure is built on at least three HPE Synergy frames
- D. if both FiexNICs are configured with the same speed
Answer: D
NEW QUESTION # 61
......
Get 100% Passing Success With True HPE0-S60 Exam: https://www.testkingit.com/HP/latest-HPE0-S60-exam-dumps.html
Premium Quality HP HPE0-S60 Online dumps: https://drive.google.com/open?id=1Po71HsrFa_nlfwDeczTDenZQ0EI6eLNT